Engineering Waterproof Product System
Cutting edge waterproofing technologies for durability and security
Category: Waterproof Coatings
Return to list
SGW109 Cementitious Capillary Crystalline Waterproof Coating

The Cementitious Capillary Crystalline Waterproof Coating is a rigid powder waterproof material made from multiple active chemical substances, with special cement, quartz sand and other materials as the matrix. To use the product, add water to make it into slurry, which is applied to the base surface of cement concrete structure. After curing, a rigid adhesive coating is formed on the surface of concrete structure. The active chemical substances contained in the coating penetrate into the concrete through permeable water carrier. It catalyzes the silicate in concrete to produce crystal which is insoluble in water, fills and blocks capillary pores and micro cracks, so as to make the concrete compact and achieve the purpose of enhancing the impermeability and waterproof protection.


Tel:+86 0594 2761989
Packaging Specification

Executive Standard

The product complies with the requirements of GB18445-2012 Cementitious Capillary Crystalline Waterproofing Materials.


Range of Application

Waterproofness and protection of underground works of industrial and civil buildings, subways, tunnels, pools, water conservancy and other concrete structures;

Water- and moisture-proofness of indoor kitchens, toilets and balconies.


地下停车场.jpg

Underground Garage

厨房.jpg

Kitchen

阳台.jpg

Balcony


Product Features
  • Simple and quick application, time saving; after application, no protective layer is needed, which reduces comprehensive cost

  • Non-toxic, harmless and environmental-friendly product, resistant to heat, damp, oxidation, carbonization, UV and radiation

  • Unique and super self-restoration capacity, and can well repair small cracks, possess long-term impermeability and withstand strong water pressure. As an inorganic material, it has no aging problem, and can achieve the same service life as concrete.

  • Super permeability, and resistant to destruction thanks to its penetration and crystallization in the concrete

Application

Usage ratios: For brushing: powder:clear water = 1:0.4

For scraping: powder:clear water = 1:0.25

Two application methods may be adopted for the product: brushing method, and dry powder spraying method:

Brushing method: 

Substrate treatment: Use a wire brush or grinder to remove floating mortar, alkali, oil stains, dust and other foreign sunstances from the surface, make the surface rough, and then wash it with water.

Ingredient mixing: Pour water into a container first, then put the powder into the water, and mechanically stir it for about 10 minutes.

Brushing: Use a hard brush to apply the coating evenly to the surface of the concrete substrate. Generally, brush 2~3 times, spray water onto or cover the surface with a wet item for maintenance after each brushing, and brush again after strength is acquired. If the previous coating has turned dry and white, it is then necessary to spray water to wet it and then brush again. When the coating film is 0.8mm thick, the usage is approximately 1.0~1.2kg/m2.

Dry powder spreading method: 

Evenly spread the powder onto the surface of the not completely solidified concrete, press the powder into the concrete with a grinder immediately and then polish it until the required effect is achieved. The usage is 1.5kg/m2.

Recommended maintenance methods: water mist, wet cloth and other water preservation methods, and the maintenance period should not be less than 72 hours.


Transportation & Storage

·This product is a non-inflammable and non-explosive material, and can be transported as general goods. During transportation, avoid exposure to sunlight, freezing, rain, extrusion and collision, and keep the package intact.

·This product should be kept ventilated, dry and protected from direct sunlight. The storage temperature is 5℃ ~35℃.

·Storage life: 12 months.


Attention

·This product is alkaline. Make sure to wear gloves during the application process. It is recommended that application personnel should wear dust-proof glasses and masks. Do not directly touch the product with hands. If you have any discomfort, please see a doctor in time.

·Pay attention to ventilation on site, and wash hands with clean water after use.

·This product is suitable for application in a 5℃~40℃ environment.

·Do not mix the dried slurry with water for use.

·The product should be sealed and kept in a ventilated, cool and dry place indoors.


Quality, Safety & Environmental Protection

Please read the product safety instructions carefully. Our safety experts would be happy to give you suggestions on safety, health and environmental protection issues.

Product Responsibility

The above information and suggestions are made based on our experience and are for reference use only. They can't replace the experiments done by customers themselves. As 3TREES and its dealers cannot control the storage, handling and use conditions of 3TREES products after delivery, no quality accidents or economic disputes caused by improper use can be attributed to our suggestions. In all application scenarios, the customer shall be responsible for abiding by the intellectual property rights of third parties.

Without our consent, technical information shall not be provided for third parties.


地址查询
专卖店授权号查询
Leave Your Message